(1) Heat. Most guys focus on reducing weight, increasing
horsepower and tuning their suspension when they want to go faster. But
factory teams know that controlling heat can make a motocross bike
significantly faster, perform better and make components last a lot
longer. The byproduct of speed is heat. Heat in the engine, radiators,
tires, suspension components, brakes, oil and fuel—you gotta get rid of
the heat to make more speed.
(2) Radiators. To get the most out of your radiators, be sure that air
entering the radiators isn’t obstructed by dirt, bent fins or damaged
louvers. Check that air doesn’t have an easier path around the
radiators, but instead is forced through them. Finally, for air to blow
through the radiators, it needs an unobstructed path to evacuate after
exiting the radiators. Aftermarket radiators from companies like Myler’s
and Fluidyne increase cooling performance by increasing the surface
areas of heat-transferring components (between the water, cores and
cooling fins), as well as using thinner materials with better heat
properties. Plastic companies like Cycra make radiator wings, number
plates and front fenders that seek to get more air through the radiators
with vents and ducting.
(3) Liquid. An aftermarket water-pump cover and impeller measurably
reduce temperatures. Pro Circuit and Boyesen offer covers that improve
circulation with better ducting and a more efficient impeller.
(4) Hoses. Increasing the radius of any sharp bends in the plumbing with
a hose kit helps the liquid flow through the system, as does
eliminating the bolt-on Y-junctions, which slows down water velocity.
Some engine tuners get really tricky and increase the surface area
between the water jacket and cylinder head. As for coolants and
additives, they often make exaggerated claims, but special coolants do a
(5) Combustion. A lean air/fuel mixture can make a bike run strong and
crisp, but there will be a correspondingly high-exhaust gas temperature
and high-cylinder head temperature. Using too low of a fuel octane
rating can cause an uneven combustion burn, leading to hotspots in the
cylinder and detonation. A lower-compression piston can reduce
combustion chamber temperature, but if the engine has to work harder to
produce the same amount of power in a given situation, it will have to
run hotter to achieve that desired output. Boosting performance with a
high-compression piston is fine, as long as you run appropriate octane fuel.
(6) Suspension. Compared to the forks, rear shocks are prone to
overheating. Since the volume of oil in a shock is very small when the
oil gets hot, its viscosity gets thinner, resulting in major shock fade.
(7) Fuel. Boiling fuel can cause vapor lock, which deprives the engine
of the amount of fuel it needs, causing it to burble or stumble. All
brands can suffer from this, but Suzukis are more prone to this than
other brands. Many pros wrap their fuel lines with insulation and cover
the underside of their fuel tank with a CV4 cover. SRS Performance makes
a suitcase-sized fuel cooler that utilizes dry ice and an electric pump
to circulate fuel through the tank or a gas can to get it cold before a
race. Even placing a fuel can in a bucket of ice works for a short
(8) Tires. A spinning rear tire on hard terrain can produce so much heat
during a moto that its air pressure can increase by up to 4 pounds.
Friction between the inner tube and tire can exacerbate that heat
buildup, so it’s important to make sure the tube and tire stay
completely clean and dry during installation. It’s equally important
that it stays clean and dry by not letting contaminents in through the
rim-lock and valve-stem holes. A pressure washer can even blast water
through nipple holes. The factory-team solution to heat-induced
tire-pressure gains is nitrogen.
(9) Brakes. Brakes are heat factories. On a fast track with heavy
braking, front- and rear-brake rotor guards can block cooling air and
cause overheating. LightSpeed offers a carbon fiber part that ducts air
into the rear caliper. Good calipers are designed with insulated
interfaces between brake pads and pistons. With larger rotors, brake systems don’t have to work as hard
and don’t produce as much heat. High-quality brake fluid is offered with
higher boiling points. For the most part, master-cylinder extenders
that advertise resistance to brake fade are less than effective because
of their distance from the heat source.
(10) Oil. Oil coolers are commonplace on factory bikes in the outdoor
series because they really work. The factories often have unobtainable
stuff, but Twin Air and Fluidyne offer good oil coolers for sale that
the MXA wrecking crew has had success with on our test bikes. They
simply route oil through metal heat sinks. It cools the oil via air
flow, while increasing its volume. As for the oil itself, not all oil is
created equal. Expensive full-synthetic engine oils, like Maxima’s
Ultra4, work better at higher temperatures than old-fashioned petroleum
oil. But while they slightly reduce friction in the engine, they also
slightly reduce friction in the clutch (unless the tranny oil is
separate). Maxima’s Premium4 petroleum-based oil is preferable to clutch
abusers. It still has some high-performance additives and is half the
price of the Ultra4. Making sure the engine has the correct amount of
oil is important. Low height makes the remaining oil work harder, get
hotter and perform worse.